Deer Stand Plans

By | January 13, 2018

Deer hunting is the most common practice now-a-days and as it is known deer is the most alert animal among others one must take utmost concern while hunting this animal. Those exploratory deer hunters, here is a great advice for you as to how you can erect an ideal Deer Stand so as to attain the best view and a perfect gunshot. There are a lot of things to be considered while preparing a Deer Stand and to get the target for which it is advisable to adopt these helpful tips while preparing a Deer Stand. You would need a list of things in order to build a perfect Deer Stand and the other vital thing is-the elevation, that helps you to get a perfect view. The elevation and its uses will be explained later. List of things to be prepared for the Deer Stand: – Lumber and plywood (pressure treated) – Ring bar 16 penny nails /3â€? sheetrock screws (for the main body of the stand) – 40 penny spikes (connected to the tree) – For the seat, take 2×2 feet plywood of width ¾â€? pt. Paint the wood with any water-proof paint until it stops absorbing any more. – A V shaped slash (cut) of 6â€?on one side-to be put against the tree. – Rise this seat on 2×4’s(2 parallel and 4 ft long) and from the 2×4’s leaving 4â€? open from front side (the notch on the behind) – And the thin or the slender side of 2×4’s against plywood. – Now inside the 2×4’s holding seat position 2 16 ft long 2×4’s with narrow side in up direction. – For adjusting the steps of the ladder (around 18â€?) now pick 2 16ft 2×4’s and wind up. – From the top most measure a distance of 18 inches that is really ideal, go on fixing stairs at 18 inches each, until you reach the base fitting each stair with 2 screws or nails on either sides of the stair. – The top piece and the ladder are done, position the top piece on the side of the ladder, position the ladder into the 2 2×4 and keep in mind that the notch has on be in the backside. – Then lean the ladder slightly about 10-15 degree rather than placing it erect, as it will be simpler for you to mount. – Fix the ladder to the seat with the help of the nails and now the stand is ready for you. – To put this on the tree take the assistance of an extension ladder, with your friend’s support place the ladder properly, with the stand next to the tree and the adjusting the seat to the desired level. – Now take a 2×4 piece and climb the ladder and with the help of nails fix it to the seat palingsso that the board tightens with the tree. – Take a 40 penny spike and coerce it across the small board and fit it with the tree. – For the braces, take a 2 4 ft long 2×4’s and nail it just ahead of the back of the plywood sheet, and down to the ladder on either sides for support, repeat this on every step fixing in the seat 2×4’s and exterior face of the ladder 2×4’s using a lot of screws and nails. – You can even construct shooting safety railing by fitting 2 4ft long 2×4’s to the braces at the spot where the ladder and the seat are combined. Elevation: – For the height, you have to position the safety railings by forwarding a bit above the seating level about 21 inches or else what you can do is for extra security on the support, take other 4ft long 2×4 on the top and another 2 4ft 2×4’s fix them again from front railing to the tree, affix with nails and screws to the front railing and 40 penny spikes along the tree. – For the back rest, take 12 by18 inch plywood and place it at a relaxed angle, fasten it between the seat and the tree and your tree stand is ready. – Finally hang a piece of cloth from the shooting railing and for the relaxation use the boat pillow, for the gun draw your ropes and now you are all set to go Elevation helps to give you a good sight while shooting and hence aiding you to never miss a perfect shot, it also secures you against all the potential troubles. You can also make it more comfortable by carpeting the interiors. To make an easy entrance construct a full-sized door.

Planning for a Deer Stand look no further, just log on at deer stand plans and to erect your own deer stand get assistance at how to build a deer stand know to erect your own comfortable Deer Stand at

Product Description
Step by step instructions with specific plans and detailed color illustrations. These plans are designed primarily to be utilized using Shop OutfitterTM tools and a PlasmaCamTM cutting table. Making use of the Lock-N-Stop Gauge (which is part of the UB-5, UB-5H Universal Bender and the UF-25H Universal Fabricator) takes the guess work out of fabricating these benches and other projects you may want to build. Without this patented gauging system that's only available on Shop OutfitterTM machines, forming the parts for these benches would be a hit and miss proposition. Metal spiral softbound. Glossy pages.

    Leave a Reply

    This site uses Akismet to reduce spam. Learn how your comment data is processed.